Ιδανική λύση για επαγγελματικές / οικιακές εφαρμογές για ακριβή μέτρηση θερμοκρασίας και εύκολη χωνευτή τοποθέτηση, σε κουτιά, πίνακες οργάνων λεβήτων, πάνελ. Δ

• Κλίμακα μέτρησης: από -55°C έως +120°C.
• Μέτρηση θερμοκρασίας με  αδιάβροχο αισθητήριο NTC10Κ
• Μήκος καλωδίου αισθητηρίου 1m
• Ακρίβεια μέτρησης ± 0,1°C.
  
• Απεικόνιση 3 ψηφίων
• Τάση λειτουργίας 110-220 VAC 
• Προέκταση καλωδίου με 0,25 ή 0,50 πολύκλωνο
• Συνθήκες λειτουργίας: θερμοκρασία -10°C - 60 °C και υγρασία 20%-85%RH
• Output: Relay Contact Capacity 10A 220V / 20A 12V
• Relay: 10A 
  
• Διαστάσεις: 79x43x26mm
• Χρώμα: μαύρο
  

Κατάλληλο για επιτήρηση και έλεγχο θερμοκρασίας σε δεκάδες εφαρμογές.

• ►Ηλιακούς θερμοσίφωνες διπλής & τριπλής ενεργείας | Κλασικούς θερμοσίφωνες μονής & διπλής ενεργείας.
• ►Υδροθερμικά ή Αερόθερμα τζάκια | Λέβητες αερίου, πετρελαίου ή στερεών καυσίμων.
• ►Αντλίες θερμότητας ή ψυκτικά μηχανήματα.
• ►Βιομηχανικές εφαρμογές σε θαλάμους ψύξης ή θέρμανσης.
• ►Αγροτικές εφαρμογές επιτήρησης και ελέγχου θερμοκρασίας.

Στην τιμή  περιλαμβάνονται το αισθητήριο.

--------------

Code Description:

Code Explanation Setting Range Factory Setting

P0 Heating / Cooling H / C C

P1 Hysteresis 0.1°C - 30°C 2.0°C

P2 Setting Limits to the Maximum P3 ~ +120°C 120°C

P3 Setting Limits to the Minimum -55°C ~ P2 -40°C

P4 Temperature Correction -10.0°C ~ 10.0°C 0.0°C

P5 Delay Start 0 - 10 minutes 0

P6 High-temp. Alarm (depends on model) ON-OFF OFF

P7 Data Lock ON-OFF OFF

P8 Factory Reset ON-OFF OFF

P9 Celsius / Fahrenheit HS / FC HS

Temperature Setting

After the temperature controller is connected to the power, the actual temperature is shown on the red

display. When you press the SET key, the blue display will flash. Press UP and DOWN keys to adjust the

temperature.

P0: Working Mode

This value should be set when you start using the thermostat. If it is used for heating, this parameter

should be set to “H”. Otherwise, if used for cooling it should be set to “C”.

P1: Hysteresis

The difference between the temperature at which the thermostat switches off - and the temperature at

which it switches on again.

Example: We set the heating mode and the temperature is 37~40°C – The hysteresis is 3°C.

P2-P3: Setting Limits

These functions set the limit values of the temperature range. Under the normal state, the setting range is

between -40°C and +120°C. If you don’t need so big range, you can set the values of these parameters to

shorten it.

Example: P2 is set to 50°C, P3 is set to 20°C – The temperature can be set from 20°C to 50°C.

P4: Temperature Correction

This function is used to correct the temperature in case there’s a deviation between the measured

temperature and the actual temperature.

Example: We measure the temperature of 25.6°C and the actual temperature is 25.8°C – You can set P4

to 0.2°C, so the displaying temperature will be 25.8°C.

P5: Delay Start

This function is generally used for cooling the refrigeration compressor. So, if you purchase the

thermostat for the refrigerator, this value has to be set to 3-6 minutes (depending on the size of the

compressor). If it doesn’t control the compressor, this value should be set to 0.

P6: High-temperature Alarm

When the actual temperature exceeds the upper temperature limit of +120°C, the thermostat will display

flashing “CCC” on the red display. In case of a short circuit, the blinking “LLL” message will be shown

on the red display.

P7: Data Lock

If you need to prevent other people from changing your set temperature, you can set P7 to ON after

finishing the setting of the parameters. After setting to ON, the temperature and the internal parameters

cannot be changed.

P8: Restore Factory Settings

By setting P8 to ON, all the settings will be reverted to their factory default.

P9: Temperature Scale

You can switch between Celsius (°C) and Fahrenheit (°F) temperature scale by modifying value of this

parameter (“HS” – Celsius, “FC” – Fahrenheit).

Setting Examples

Cooling Mode

Controlling refrigeration equipment will stop cooling when the temperature is 25°C and start cooling

when the temperature is 30°C. To set the working mode like this, follow the next steps:

1. In the state of displaying the normal temperature, press the SET key to get the flashing numbers

on the blue display; find the value 25.0°C by navigating with UP and DOWN buttons and finally

press the RESTART key to confirm and get back to display state.

2. To access the parameter setting mode, press the SET key and hold it for 5 seconds until “P0”

appears on the screen. Then press the SET key to access the P0 code parameter. By pressing UP /

DOWN, you can adjust between different modes. Choose “C” mode and press the RESTART key

to confirm and get back to display state.

3. Go to parameter setting mode again by holding the SET key for 5 seconds. When P0 is displayed

on the screen, press the UP button to adjust to the code P1 (hysteresis) and then press SET to

access the P1 code parameter. Adjust the value to 5.0 by navigating with UP/DOWN buttons and

finally press the RESTART key to confirm and get back to display state.

If you need to set other parameters, please refer to above settings.

Heating mode

Controlling heating equipment will stop heating when the temperature is 30°C and start heating when the

temperature is 25°C. To set the working mode like this, follow the next steps:

1. In the state of displaying the normal temperature, press the SET key to get the flashing numbers

on the blue display; find the value 25.0°C by navigating with UP and DOWN buttons and finally

press the RESTART key to confirm and get back to display state.

2. To access the parameter setting mode, press the SET key and hold it for 5 seconds until “P0”

appears on the screen. Then press the SET key to access the P0 code parameter. By pressing UP /

DOWN, you can adjust between different modes. Choose “H” mode and press the RESTART key

to confirm and get back to display state.

3. Go to parameter setting mode again by holding the SET key for 5 seconds. When P0 is displayed

on the screen, press the UP button to adjust to the code P1 (hysteresis) and then press SET to

access the P1 code parameter. Adjust the value to 5.0 by navigating with UP/DOWN buttons and

finally press the RESTART key to confirm and get back to display state.

If you need to set other parameters, please refer to above settings.